Trask Research, Inc.  

 

    Home        Contact       Policies      Shipping      Order

 

 
  Mold Products Division
 
 
       

Oxy-Mold MX-500
MATERIAL SAFETY DATA SHEET
(Prepared According to 29 CFR 1910.1200)

SECTION I - PRODUCT IDENTIFICATION Oxy-Mold MX-500
Trask Research, Inc.
2723 Brickton North Drive
Buford, GA 30515
Date of Preparation: September 2, 2006
Information Telephone Number; 770-904-2499
Emergency Telephone Numbers: 770-904-2499
Weekdays: 770-904-2499
After hours, None
Emergency Contact Number: Poison Control Center
SECTION II - INGREDIENT INFORMATION

CHEMICAL NAME
Water
Dimethyl Benzyl Ammonium Chloride
Dimethyl Ethylbenzyl Ammonium Chloride
Nonionic Surfactant
Sodium Carbonate
Tetrasodium EDTA
Perfume Oil
Dye

CAS NO.
7732-18-5
68391-01-5
68956-79-6
9016-45-9
N/A
N/A

N/A
N/A

WT. %
to 100
0.781
0.781
0 to 5
0 to 5
0 to 5
0 to 5
0 to 5

PEL TWA-TLVSTEL-TLV
This product does not contains any toxic chemical(s) subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 and of 40 CFR 372.
SECTION III - PHYSICAL DATA
Boiling Point (F): 210 F.
Specific Gravity: 1.040
Vapor Pressure: 20mm Hg @ 68 F.
Vapor Density (Air=1): >1
% Volatile: 90+
pH: 11.5-12.0
Solubility in Water: Complete
Evaporation Rate (Water=1): <1
Physical Description: Thin
liquid with light lemon scent
SECTION IV - FIRE AND EXPLOSION HAZARD DATA

Flash Point (Method Used): N/A
Upper Explosion Limit: N/A

Lower Explosion Limit: N/A
Extinguishing Media: N/A

Special Firefighting Procedures: Non Flammable
Unusual Fire and Explosion Hazards: N/A

SECTION V - REACTIVITY DATA

Stability: Stable
Hazards Decomposition Products: Will not occur.

Hazardous Polymerization: None
Incompatibility (Materials to Avoid): None

SECTION VI - STORAGE AND HANDLING INFORMATION
Keep out of reach of children. For use by trained personnel only. Keep container closed during storage. For institutional and industrial use only. Avoid contact with eyes, skin and clothing. Avoid breathing of mists. Use in well-ventilated area.

SECTION VII - HEALTH HAZARDS AND FIRST AID

Effects of Overexposure:
Skin: Skin irritant. Prolonged or repeated contact may cause dermatitis.
Eyes: Severe eye irritant. Liquid and mists may injure the eyes causing corneal damage.
Inhalation: Mists are irritating to throat, nose and lungs.
Ingestion: Irritating to the mouth, throat, and gastrointestinal system. Burning, pain, and diarrhea expected with large doses.

First Aid Procedures:
Skin: Remove contaminated clothing. Flush affected areas with large quantities of water. Seek medical attention if irritation persists.
Eyes: Flush with large quantities of water, holding eyelids open. Seek medical attention.
Inhalation: Remove victim to fresh air and monitor. Seek medical attention if symptoms persist.
Ingestion: Give large quantities of water. Seek medical attention immediately.

SECTION VIII - SPECIAL PROTECTION INFORMATION

Respiratory Protection: Wear an P100 or better rated respirator. Avoid breathing mists. Ventilate before re-entry to area.
Ventilation Requirements: Provide local exhaust to keep TLV of Section 2 ingredients below acceptable limit.
Protective Gloves: Latex, rubber, vinyl, or nitrile Eye Protection: Chemical goggles recommended when spraying diluted product.
Other Protective Equipment: Eye protection should be worn during appliaction. Eyewash station should be provided nearby.

SECTION IX - SPILL OR LEAK PROCEDURES

Steps to be taken in Case Material is Released or Spilled: Floors will become slippery. Avoid walking in product. Keep unessential personnel away. Mop up or otherwise absorb and hold disposal. Avoid discharge to sewer or open waterways.
Waste Disposal Method: Any method in accordance with local, state and federal laws. Best method is to recycle or reuse for intended purpose. Consult local authorities for disposal in public sewer. Do not dispose of into storm drain, stream, river or to ground. Rinse container thoroughly before discarding in trash.

SECTION X - REGULATORY INFORMATION

SARA Title III - Section 311/312 - Hazard Categories:
No - Fire Hazard
No - Sudden Release of Pressure Hazard
No - Reactivity Hazard
Yes - Immediate (acute) Health Hazard

No - Delayed (chronic) Health Hazard Shipping Class: Cleaning Compound
To comply with New Jersey DOH Right-To-Know labeling law (N.J.A.C. 8:59 - 5.1 & 5.2)
 
CAS. No.:
7732-18-5
68391-01-5
68956-79-6
9016-45-9
 
CHEMICAL INGREDIENTS:
Water
Dimethyl Benzyl Ammonium Chloride
Dimethyl Ethylbenzyl Ammonium Chloride
Nonionic Surfactant
HMIS HAZARD RATING
Health 2 Flammability 0 Physical Hazard 0 Personal Protection B
HAZARD INDEX: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe
 
                                     
 

Questions?  Contact:  mold@traskresearch.com


Home     Contact     Policies     Mold Products     Health Products     Shipping     Order

 

2004-2006 Trask Research, Inc.   2723 Brickton North Drive, Buford, GA 30518

 

Disclaimer

This is an informational website about mold, it's health effects, and how to treat it. Although Trask Research, Inc. believes it to be accurate, Trask Research, Inc. make no representation, warranty or guaranty, and disclaims any liability, with regard to the accuracy or completeness of the information, or the results of any action taken by anyone who relies on the information. If you have any question regarding your particular application, we ask that you seek professional advice and assistance in your area. Trask Research, Inc. is not responsible for any damage or loss due to the use of this information. Use this and any information obtained at this web site at your own risk.